Select Page

Build the Ultimate Container Storage Cabinet

Build the Ultimate Container Storage Cabinet

 FH18DJF_583_00_027 supreme container storage cabinet tupper wear kitchen area company Build the Ultimate Container Storage Cabinet Tools and products

Our 24-in. base cabinet needed a 4 x 4-ft. sheet of 1/2-in.- thick plywood for the rollout, plus a 2 x 3-ft. scrap of 3/4-in. plywood for the provider. Your container storage cabinet might need basically. We discovered top quality birch plywood at a house center for this develop the supreme container storage cabinet task. If you have problem discovering great plywood, think about purchasing Baltic birch or ApplePly plywood from a house center or regional lumberyard . The provider fits under the rollout and isn’’ t really noticeable, so practically any flat piece of 3/4-in. plywood will work for that.

In addition to the lumber, you’’ ll require a set of 22-in. full-extension ball-bearing slides (about $22 in the house centers or woodworking supply shops) and a 1/4-in. aluminum rod.

We utilized a table saw to cut the plywood parts, however if you’’ re cautious to make precise cuts, a circular saw will work. You’’ ll require a jigsaw with a plywood-cutting blade to cut the curves on the dividers and sides. We utilized a surface nail weapon and 1-1/4- in.- long brad nails to link the parts, however you might replace trim-head screws if you wear’’ t mind the bigger holes they leave. Keep reading to find out how to develop this container storage cabinet .

.Develop the Ultimate Container Storage Cabinet Project Directions:.

 FH18DJF_583_55_019 container storage cabinet procedure

.1. Step the opening of the base cabinet.

Most base cabinets have to do with 23 in. deep and will accommodate this container storage cabinet rollout, however step yours to be sure. If the measurement from the back of the face frame to the back of the cabinet is less than 22 in., you’’ ll need to develop a shallower rollout and usage much shorter drawer slides.

The other important measurement is the width. Procedure the clear opening width; that is, the width from any extending hinge or door parts to the opposite side of the cabinet opening (Photo above). Deduct 3 in. from this measurement to identify the width of parts B, E, c and d (as seen listed below in Project PDF’’ s– Figure A).

 FH18DJF_583_55_002 supreme container storage cabinet side

.2. Cut the side panels.

After changing the size of parts B, C, D and E for the container storage cabinet width, you can eliminate all the parts other than the provider bottom. If you’’ re utilizing a table saw, make partial cuts to form the L-shaped sides. Keep in mind, you can’’ t see how far the blade is cutting on the underside, so be sure to stop brief of your inside corner marks by at least an inch. The image above demonstrate how to finish the cut with a jigsaw.

 FH18DJF_583_55_004 cut the curves container storage cabinet

.3. Cut the curves.

Trace along the edge of a 1-gallon paint can to draw the radius for the curve on the side panels. Trace along a quartsize can to draw the radius on the dividers. Cut the curves on the sides and dividers with a jigsaw (Photo above). Smooth the curved cuts with 100-grit sandpaper.

 FH18DJF_583_55_008 rollout container storage cabinet

.4. Put together the rollout.

Mark the area of the 1/4-in. rod on the side panels utilizing Figure A ( in Project PDFs listed below) as a guide. Wrap tape around a 1/4-in. drill bit 1/4 in. from completion to utilize as a depth guide while drilling. Drill 1/4-in.- deep holes at the marks. Utilize a hacksaw to cut an aluminum rod 1/2 in. longer than the width of the bottom.

Apply wood glue to all edges that satisfy, and set up the sides, bottom, front and back on a workbench and secure them together. Work the aluminum rod into the holes. Tap the parts with a hammer to line up the edges completely prior to linking them with brad nails (Photo above). Take your time intending the nail weapon to prevent nail blowouts.

 FH18DJF_583_55_010 dividers container storage cabinet

.5. Nail the dividers to the rack.

Finish the rollout by including the dividers. Choose how numerous dividers you determine the width and desire of the area in between the dividers. Cut a spacer block to that measurement and utilize it as a guide to set up the dividers. Connect the dividers to the rack (Photo above).

 FH18DJF_583_55_011 container storage cabinet

.6. Nail the dividers to the rollout and cut provider.

Then determine down 7-1/2 in. from the leading and make marks to suggest the leading edge of the divider rack. Line up the divider assembly with these marks and nail it in. Draw divider center lines on the back of the rollout as a nailing guide. Connect the dividers (Photo above).

Drawer slides need 1/2-in. clearance on each side, so making the provider precisely 1 in. broader than the rollout will lead to a best fit. Procedure the width of the finished rollout and include precisely 1 in. to figure out the width of the provider bottom. Cut the provider bottom from 3/4-in. plywood. Screw the provider sides to the provider bottom to prepare the provider for installing the drawer slides.

 FH18DJF_583_55_013 drawer slide rail

.7. Screw the drawer slide to the rollout.

Follow the guidelines consisted of with your drawer slides to separate the slides into 2 parts: a rail and a channel. Typically, pushing down on a plastic lever launches the parts and enables you to separate them. Screw the rails to the drawer (Photo above).

 FH18DJF_583_55_017 provider drawer slide channel

.8. Screw the drawer slide channel to the provider.

Rest the drawer slide channel on the provider and line up the front flush to the front of the provider side. When you’’ re done setting up the slides, inspect the fit by thoroughly lining up the rails with the channels and moving them together. The rollout needs to move quickly on the ball-bearing slides. If the slides appear too tight, you can change the fit by eliminating among the provider sides and slipping a thin cardboard shim in between the provider side and provider bottom prior to reassembling them.

 FH18DJF_583_55_023 set up provider to cabinet

.9. Set up the provider.

The picture above programs fitting the provider assembly into the cabinet. There will be a little side-to-side play, so you can change the position to clear the hinge and door. This will most likely need you to balance out the provider a little far from the hinge side.

 FH18DJF_583_55_026 set up the container storage cabinet rollout 10. Set up the rollout.

Screw the provider to the bottom of the cabinet and you’’ re prepared to set up the rollout (Photo above). Given that you’’ ve currently inspected the fit, it needs to run completely. Now load it up with covers and containers and enjoy your nicely arranged container rollout.

Find more cooking area storage and company concepts here .

.Develop the Ultimate Storage Container Cabinet Project PDFs.

Click the links listed below to download the products and cutting lists for this job. As the jobs building illustrations.

Cutting List and Project Drawings —– Figure A

Materials List

.

Read more: familyhandyman.com

Click here to get this post in PDF

About The Author

Leave a reply

Your email address will not be published. Required fields are marked *